With Drone Manager, you see your account's drones on a live map in the Dronelink web app. Owners and admins of the account can also send commands to a drone, for example Return Home or Pause Mission.
Drone Manager is part of the Growth, Enterprise and Education plans. To see which plans include it, see the plan comparison.
What you need
- An account with a plan that includes Drone Manager.
- The Dronelink app, version 5.5.0 or later, on the phone, tablet or controller that flies the drone.
- An internet connection on that device. Without it, the drone does not show in Drone Manager.
Show a drone in Drone Manager
- In the Dronelink app, sign in and select the account that has Drone Manager.
- Connect the drone.
The drone shows in Drone Manager in a few seconds. Each member of the account who flies a drone this way adds it to the list.
Open Drone Manager
- Go to app.dronelink.com and open your account.
- Click the Drones tab at the bottom of the account panel.
The list shows each drone of the account that was connected in the last 24 hours. The map shows where each drone is.
Read a drone card
Each card shows the drone name, the pilot, the flight mode and the status messages of the drone. When the drone is connected, the card also shows the battery, the flight time, the GPS satellites and the signal strength. Turn on Details to show more information on each card.
The chips above the list count the drones in each state, for example Not Flying or Disconnected. Click a chip to show only those drones. A drone shows as disconnected when the app sends no update for 10 seconds.
Send a command
Only owners and admins of the account can send commands. Other members see the same map and cards, but no commands.
A command goes to the drone only while the drone is connected.
To send a command from the menu:
- On the drone card, click the menu (the three dots).
- Click the command.
- If Dronelink asks you to confirm, click OK.
The menu has these commands:
- Takeoff: when the drone is on the ground.
- RTH (Return Home): when the drone flies.
- Format SD Card: deletes all photos and videos on the drone's SD card.
The card has these controls:
- Load Plan: select a plan of the account. The pilot's app loads it.
- The round mission button: click it to start or resume the loaded mission, or to pause it while it runs. The ring around the button shows the progress of the mission.
- The X on the loaded plan: closes the plan in the pilot's app.
- The Returning Home or Landing chip: click it to cancel the return or the landing.
Stop All pauses the missions of all drones that fly a mission.
WARNING: Before you send Takeoff, make sure that the pilot is at the controller and that the area around the drone is clear. The drone takes off without an action of the pilot. A drone that takes off near people can cause injury.
CAUTION: Before you send Format SD Card, make sure that the pilot does not need the photos and videos on the card. Format SD Card deletes them, and you cannot get them back.
Know if a command ran
The card shows the command while the pilot's app runs it, for example Starting....
- If the app did not run the command, the card shows Not run and the command. Move the pointer over it to see the reason.
- If the app does not answer in 60 seconds, the card shows No answer from the pilot's app. The app does not run a command that is older than 45 seconds, so send the command again if it is still necessary.
What the pilot sees
The pilot always knows when Drone Manager can send commands to the drone:
- The first time a drone connects in an account with Drone Manager, the app shows a notice that owners and admins can see the drone and send it commands.
- The flight screen shows the Drone Manager icon to the left of the battery. The pilot can tap the icon to read what it means.
- When a command runs, the app shows the command and the name of the person who sent it.
The pilot can take control with the remote controller at any time. A command from Drone Manager does not stop the pilot.
Deconflict
Deconflict (in this browser) pauses the missions of drones that come too close to each other. It works only while the Drones page is open in your browser.
WARNING: Do not use Deconflict as collision avoidance. It stops when you close the page or when your computer loses its internet connection. The pilots must always watch their drones.
Limits
- The pilot's device needs an internet connection. The app sends the drone's position every second in flight and every 5 seconds on the ground.
- A drone stays in the list for 24 hours after its last connection. You cannot remove it from the list.
- Drone Manager shows only drones that fly with an account that has Drone Manager selected in the app.